Standard Specification for Bonded Copper Conductors for Use in Hookup Wires for Electronic Equipment
Standard Specification for Bonded Copper Conductors for Use in Hookup Wires for Electronic EquipmentB0470-02R24ASTM|B0470-02R24|en-USStandard Specification for Bonded Copper Conductors for Use in Hookup Wires for Electronic EquipmentStandardB470 Standard Specification for Bonded Copper Conductors for Use in Hookup Wires for Electronic Equipment>newBOS Vol. 02.03 Committee B01
$64.00
In stock
ASTM International
Abstract
This specification covers stranded uninsulated bare, tin, or tin-lead alloy coated copper conductors in which wires in the strand are metallically bonded together by the application of heat additional tin, or tin-lead alloy for use in hookup wire for electronic equipment. Conductor constructions shall conform to standard ASTM requirements except that, in addition, the following bondings may be specified: Type I, Type II, and Type III. The conductors shall consist of tinned copper and bare copper, conforming to product description, quality, and specification requirements. The material shall undergo flex, fraying, mandrel, and resistance tests. The material shall meet the minimum flex life requirements and shall conform to the required conditions for flex, fraying, and madrel tests.
Scope
1.1 This specification covers stranded uninsulated bare, tin, or tin-lead alloy coated copper conductors in which wires in the strand are metallically bonded together by the application of heat or additional tin, or tin-lead alloy for use in hookup wire for electronic equipment.
1.2 The SI values for density and resistivity are to be regarded as standard. For all other properties, the inch-pound values are to be regarded as the standard and the SI units may be approximate.
1.3The hazard caveat pertains only to Section 6 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Domestic orders are delivered via United Parcel Service (UPS) or United States Postal Service (USPS). Transit
times average 3 to 5 business days. Please be aware that UPS will not deliver packages to Post Office Boxes.
International orders are delivered via courier post services which can be either a postal service, courier
service, or a combination of both. Standard Service is untraceable. Please allow 4-7 weeks for delivery.
Please be aware that carriers will not deliver packages to Post Office Boxes. Because of the variability of
customs processes and procedures in different countries, ASTM International cannot guarantee transit times to
international destinations. Customs duty and taxes are the responsibility of the consignee.
Shipping & Handling charges follow the rate schedule, below:
Order Total
Shipping & Handling Fee (US Domestic)
Up to $50.00
$19.47
$50.01 to $100.00
$21.63
$100.01 to $150.00
$30.70
$150.01 to $250.00
$40.66
$250.01 to $500.00
$58.50
$500.01 to $750.00
$79.48
$750.01 to $1000.00
$96.88
$1000.01 to $1500.00
$126.13
$1500.01 to $2500.00
$164.72
$2500.01 to $4999.00
$217.40
$5000.00 to higher
FREE
Order Total
Shipping & Handling Fee (International)
Up to $50.00
$69.47
$50.01 to $100.00
$71.63
$100.01 to $150.00
$80.70
$150.01 to $250.00
$90.66
$250.01 to $500.00
$108.50
$500.01 to $750.00
$129.48
$750.01 to $1000.00
$146.88
$1000.01 to $1500.00
$176.13
$1500.01 to $2500.00
$214.72
$2500.01 to $4999.00
$267.40
$5000.00 to higher
FREE
Shipping and Handling charges are approximate. Additional charges may be incurred if your order requires multiple shipments. This does not apply to complete sets and sections.