Standard Practice for Preparing Resin Solutions for Viscosity Measurement by Bubble Time Method
Standard Practice for Preparing Resin Solutions for Viscosity Measurement by Bubble Time MethodD1725-12R19ASTM|D1725-12R19|en-USStandard Practice for Preparing Resin Solutions for Viscosity Measurement by Bubble Time MethodStandardD1725 Standard Practice for Preparing Resin Solutions for Viscosity Measurement by Bubble Time Method>newBOS Vol. 06.03 Committee D01
$64.00
In stock
Abstract
This test method details the standard procedure for measuring the viscosity of resin solutions. The apparatuses required here are constant-temperature water bath, wide-mouthed screw capped bottles, cellophane sheets, No. 2 short taper corks, viscosity tube holder, bottle shaker, timing device, and viscosity tubes. Solid resins are dissolved in organic solvents by cold-cut or hot-cut methods in the laboratory. The viscosity of such prepared solutions, or of commercial solutions of resins is then determined by the bubble time method. The bubble seconds are approximately equal to stokes.
Scope
1.1 This practice provides instructions for preparing resin solutions viscosity measurement by bubble time method.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Domestic orders are delivered via United Parcel Service (UPS) or United States Postal Service (USPS). Transit
times average 3 to 5 business days. Please be aware that UPS will not deliver packages to Post Office Boxes.
International orders are delivered via courier post services which can be either a postal service, courier
service, or a combination of both. Standard Service is untraceable. Please allow 4-7 weeks for delivery.
Please be aware that carriers will not deliver packages to Post Office Boxes. Because of the variability of
customs processes and procedures in different countries, ASTM International cannot guarantee transit times to
international destinations. Customs duty and taxes are the responsibility of the consignee.
Shipping & Handling charges follow the rate schedule, below:
Order Total
Shipping & Handling Fee (US Domestic)
Up to $50.00
$18.72
$50.01 to $100.00
$20.80
$100.01 to $150.00
$29.52
$150.01 to $250.00
$39.09
$250.01 to $500.00
$56.25
$500.01 to $750.00
$76.42
$750.01 to $1000.00
$93.15
$1000.01 to $1500.00
$121.27
$1500.01 to $2500.00
$158.38
$2500.01 to $4999.00
$209.04
$5000.00 to higher
FREE
Order Total
Shipping & Handling Fee (International)
Up to $50.00
$68.72
$50.01 to $100.00
$70.80
$100.01 to $150.00
$79.52
$150.01 to $250.00
$89.09
$250.01 to $500.00
$106.25
$500.01 to $750.00
$126.42
$750.01 to $1000.00
$143.15
$1000.01 to $1500.00
$171.27
$1500.01 to $2500.00
$208.38
$2500.01 to $4999.00
$259.04
$5000.00 to higher
FREE
Shipping and Handling charges are approximate. Additional charges may be incurred if your order requires multiple shipments. This does not apply to complete sets and sections.