Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire

Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire B0107_B0107M-12 ASTM|B0107_B0107M-12|en-US Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire Standard B107/B107M Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire> new BOS Vol. 02.02 Committee B07

$ 96.00 In stock

Abstract

This specification covers magnesium-alloy extruded bars, rods, profiles, tubes, and wire. The bars, rods, profiles, tubes, or wire shall conform to the chemical requirements specified. Tensile properties such as tensile strength, yield strength, and elongation of magnesium alloys shall be determined. All material shall be of uniform quality, free from injurious surface defects, and shall have a workmanlike finish.

Scope

1.1 This specification covers magnesium-alloy extruded bars, rods, profiles, tubes, and wire of the composition given in Table 1.

TABLE 1 Chemical Requirements^A

Note 1—Analysis shall regularly be made only for the elements specifically mentioned in this table. If, however, the presence of other elements is suspected or indicated in the course of routine analysis to be in amounts greater than the specified limits, further analysis shall be made to determine that the total of these other elements is not in excess of the limits specified in the last column of the table.

Note 2—The following applies to all specified limits in this table: For purposes of acceptance and rejection, an observed value or a calculated value obtained from analysis should be rounded-off to the nearest unit in the last right-hand place of figures used in expressing the specified limit.

Alloy^B		Composition, %
UNS No.	ASTM No.	Magnesium	Alumi- num	Cal- cium	Cop- per	Iron	Lithium	Man- ganese	Neodymium	Nickel	Rare Earths	Sili- con	Yttrium	Zirco- nium, min	Zinc	Other Impurities, each	Total Other^C Impurities
M11311	AZ31B	remainder	2.5-3.5	0.04	0.05	0.005		0.20-1.0		0.005		0.10		...	0.6-1.4		0.30
M11312	AZ31C	remainder	2.4-3.6	...	0.10	...		0.15-1.0^D		0.03		0.10		...	0.50-1.5		0.30
M11610	AZ61A	remainder	5.8-7.2	...	0.05	0.005		0.15-0.5		0.005		0.10		...	0.40-1.5		0.30
M11800	AZ80A	remainder	7.8-9.2	...	0.05	0.005		0.12-0.5		0.005		0.10		...	0.20-0.8		0.30
M15100	M1A	remainder	...	0.30	0.05	...		1.2-2.0		0.01		0.10		...	...		0.30
M18432	WE43B	remainder	...	...	0.02	0.010	0.2	0.03	2.0-2.5	0.005	1.9^E	...	3.7-4.3	0.40-1.0	^F	0.01	...
M18410	WE54A	remainder	...	...	0.03	...	0.2	0.03	1.5-2.0	0.005	2.0^E	0.01	4.75-5.5	0.40-1.0	0.20	0.2	...
M16400	ZK40A	remainder	...	...	...	...		...		...		...		0.45	3.5–4.5		0.30
M16600	ZK60A	remainder	...	...	...	...		...		...		...		0.45	4.8-6.2		0.30

^A Limits are in weight percent maximum unless shown as a range or otherwise stated.

^B These alloy designations were established in accordance with Practice B951 (see also Practice E527).

^C Includes listed elements for which no specific limit is shown.

^D Manganese minimum limit need not be met if iron is 0.005 %, or less.

^E Other Rare Earths shall be principally heavy rare earths, for example, Gadolinium, Dysprosium, Erbium, and Ytterbium. Other Rare Earths are derived from the Yttrium, typically 80 % Yttrium 20 % heavy rare earths.

^F Zinc + Silver content shall not exceed 0.20 % in WE43B.

1.2 The values stated in either inch-pound or SI units are to be regarded separately as standards. The SI units are shown in brackets or in separate tables or columns. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.

1.3 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.

Version

Language

Format

Price:

Shipping & Handling

Domestic Shipping

Domestic orders are delivered via United Parcel Service (UPS) or United States Postal Service (USPS). Transit times average 3 to 5 business days. Please be aware that UPS will not deliver packages to Post Office Boxes.

Domestic Rush Orders

Please Contact Us.

International Standard Shipping

International orders are delivered via courier post services which can be either a postal service, courier service, or a combination of both. Standard Service is untraceable. Please allow 4-7 weeks for delivery.

International Expedited Shipping

Please Contact Us.

Please be aware that carriers will not deliver packages to Post Office Boxes. Because of the variability of customs processes and procedures in different countries, ASTM International cannot guarantee transit times to international destinations. Customs duty and taxes are the responsibility of the consignee.

Shipping & Handling charges follow the rate schedule, below:

Order Total	Shipping & Handling Fee (US Domestic)
Up to $50.00	$18.72
$50.01 to $100.00	$20.80
$100.01 to $150.00	$29.52
$150.01 to $250.00	$39.09
$250.01 to $500.00	$56.25
$500.01 to $750.00	$76.42
$750.01 to $1000.00	$93.15
$1000.01 to $1500.00	$121.27
$1500.01 to $2500.00	$158.38
$2500.01 to $4999.00	$209.04
$5000.00 to higher	FREE

Order Total	Shipping & Handling Fee (International)
Up to $50.00	$68.72
$50.01 to $100.00	$70.80
$100.01 to $150.00	$79.52
$150.01 to $250.00	$89.09
$250.01 to $500.00	$106.25
$500.01 to $750.00	$126.42
$750.01 to $1000.00	$143.15
$1000.01 to $1500.00	$171.27
$1500.01 to $2500.00	$208.38
$2500.01 to $4999.00	$259.04
$5000.00 to higher	FREE

Shipping and Handling charges are approximate. Additional charges may be incurred if your order requires multiple shipments. This does not apply to complete sets and sections.

ASTM License Agreement

Reprints and Permissions

Reprints and copyright permissions can be requested through the
Copyright Clearance Center

Details

Book of Standards Volume: 02.02

Developed by Subcommittee: B07.04

Pages: 19

DOI: 10.1520/B0107_B0107M-12

ICS Code: 77.150.20

Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire

Related

Reprints and Permissions

Details