Spray droplet size has long been recognized as the most important variable that aerial applicators can influence to mitigate spray drift from the application site. There are several different technologies that are used by researchers to measure droplet size from spray nozzles. The objective of these studies was to determine the influence of eight spray adjuvants on the droplet size spectrum produced by two nozzles in a high-speed wind tunnel when characterized using three different droplet size measurement systems. The adjuvant, nozzles, and airspeeds used in these studies are commonly used by aerial applicators. Three droplet sizing systems (Malvern laser diffraction, PMS optical array probe, and LaVision laser imaging) were simultaneously operated to measure the spray droplet size spectra for each adjuvant, airspeed, and nozzle combination. Two spray nozzles (a D6-46 nozzle and a D2 straight stream nozzle) were evaluated in a high-speed wind tunnel at airspeeds of 45 and 58 m/sec. There were significant differences in the droplet size spectra produced by the eight spray adjuvants tested. There were also significant differences between the droplet size values reported by the three measurement systems (Malvern, LaVision, and PMS) evaluated; however, there was considerable agreement trendwise. In general, the Malvern reported smaller spray droplet size spectra values than the LaVision, while the PMS system generally reported the largest spray droplet size spectra values. These tests are the first reported studies where all three droplet sizing systems were operated simultaneously.
Author Information
Hoffmann, W., Clint
USDA-ARS-Areawide Pest Management Research Unit, College Station, TX
Hewitt, A., J.
University of Queenland, Gatton, Australia
Ross, J., B.
New Mexico State University, Las Cruses, NM
Bagley, W., E.
Wilbur-Ellis Company, San Antonio, TX
Martin, D., E.
USDA-ARS-Areawide Pest Management Research Unit, College Station, TX
Fritz, B., K.
USDA-ARS-Areawide Pest Management Research Unit, College Station, TX
Domestic orders are delivered via United Parcel Service (UPS) or United States Postal Service (USPS). Transit
times average 3 to 5 business days. Please be aware that UPS will not deliver packages to Post Office Boxes.
International orders are delivered via courier post services which can be either a postal service, courier
service, or a combination of both. Standard Service is untraceable. Please allow 4-7 weeks for delivery.
Please be aware that carriers will not deliver packages to Post Office Boxes. Because of the variability of
customs processes and procedures in different countries, ASTM International cannot guarantee transit times to
international destinations. Customs duty and taxes are the responsibility of the consignee.
Shipping & Handling charges follow the rate schedule, below:
Order Total
Shipping & Handling Fee (US Domestic)
Up to $50.00
$18.72
$50.01 to $100.00
$20.80
$100.01 to $150.00
$29.52
$150.01 to $250.00
$39.09
$250.01 to $500.00
$56.25
$500.01 to $750.00
$76.42
$750.01 to $1000.00
$93.15
$1000.01 to $1500.00
$121.27
$1500.01 to $2500.00
$158.38
$2500.01 to $4999.00
$209.04
$5000.00 to higher
FREE
Order Total
Shipping & Handling Fee (International)
Up to $50.00
$68.72
$50.01 to $100.00
$70.80
$100.01 to $150.00
$79.52
$150.01 to $250.00
$89.09
$250.01 to $500.00
$106.25
$500.01 to $750.00
$126.42
$750.01 to $1000.00
$143.15
$1000.01 to $1500.00
$171.27
$1500.01 to $2500.00
$208.38
$2500.01 to $4999.00
$259.04
$5000.00 to higher
FREE
Shipping and Handling charges are approximate. Additional charges may be incurred if your order requires multiple shipments. This does not apply to complete sets and sections.