Standard Specification for Design and Performance of a Light Sport Airplane
Standard Specification for Design and Performance of a Light Sport AirplaneF2245-12DASTM|F2245-12D|en-USStandard Specification for Design and Performance of a Light Sport AirplaneStandardF2245 Standard Specification for Design and Performance of a Light Sport Airplane>newBOS Vol. 15.09 Committee F37
$125.00
In stock
Abstract
This specification covers airworthiness requirements for the design of powered fixed wing light sport aircraft, an �airplane.� In order to comply with flight requirements, the following shall be evaluated: load distribution limit, propeller speed and pitch limit, stalling speed, takeoff, climb, landing, balked landing, controllability and maneuverability, vibrations, and ground control and stability. For compliance of structure requirements, the following shall be considered: flight loads; control surface and system loads; horizontal stabilizing and balancing surfaces (balancing loads, maneuvering loads, and gust loads); vertical stabilizing surfaces (maneuvering loads, gust loads, and outboard fins or winglets); supplementary conditions for stabilizing surfaces; ailerons, wing flaps, and special devices; ground load conditions; water load conditions; emergency landing conditions; and other loads. The aircraft shall be designed with the following minimum instrumentation and equipment: flight and navigation instruments such as airspeed indicator, and altimeter; powerplant instruments such as fuel quantity indicator, tachometer (RPM), engine �kill� switch, and engine instruments; miscellaneous equipment such as master switch, and overload protection device; and safety belts and harnesses. Each airplane shall include a Pilot Operating Handbook (POH).
Scope
1.1 This specification covers airworthiness requirements for the design of powered fixed wing light sport aircraft, an “airplane.”
1.2 This specification is applicable to the design of a light sport aircraft/airplane as defined by regulations and limited to VFR flight.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
Domestic orders are delivered via United Parcel Service (UPS) or United States Postal Service (USPS). Transit
times average 3 to 5 business days. Please be aware that UPS will not deliver packages to Post Office Boxes.
International orders are delivered via courier post services which can be either a postal service, courier
service, or a combination of both. Standard Service is untraceable. Please allow 4-7 weeks for delivery.
Please be aware that carriers will not deliver packages to Post Office Boxes. Because of the variability of
customs processes and procedures in different countries, ASTM International cannot guarantee transit times to
international destinations. Customs duty and taxes are the responsibility of the consignee.
Shipping & Handling charges follow the rate schedule, below:
Order Total
Shipping & Handling Fee (US Domestic)
Up to $50.00
$18.72
$50.01 to $100.00
$20.80
$100.01 to $150.00
$29.52
$150.01 to $250.00
$39.09
$250.01 to $500.00
$56.25
$500.01 to $750.00
$76.42
$750.01 to $1000.00
$93.15
$1000.01 to $1500.00
$121.27
$1500.01 to $2500.00
$158.38
$2500.01 to $4999.00
$209.04
$5000.00 to higher
FREE
Order Total
Shipping & Handling Fee (International)
Up to $50.00
$68.72
$50.01 to $100.00
$70.80
$100.01 to $150.00
$79.52
$150.01 to $250.00
$89.09
$250.01 to $500.00
$106.25
$500.01 to $750.00
$126.42
$750.01 to $1000.00
$143.15
$1000.01 to $1500.00
$171.27
$1500.01 to $2500.00
$208.38
$2500.01 to $4999.00
$259.04
$5000.00 to higher
FREE
Shipping and Handling charges are approximate. Additional charges may be incurred if your order requires multiple shipments. This does not apply to complete sets and sections.
