Standard Practice for Pressing and Drying Refractory Plastic and Ramming Mix Specimens
Standard Practice for Pressing and Drying Refractory Plastic and Ramming Mix SpecimensC1054-13ASTM|C1054-13|en-USStandard Practice for Pressing and Drying Refractory Plastic and Ramming Mix SpecimensStandardC1054 Standard Practice for Pressing and Drying Refractory Plastic and Ramming Mix Specimens>newBOS Vol. 15.01 Committee C08
$77.00
In stock
Significance and Use
3.1 This practice is useful for producing uniform specimens of refractory plastics and ramming mixes for use in standard ASTM tests. Samples thus formed may be used for referee testing when setting specifications between producer and user. Establish by mutual agreement and specify in the report the forming parameters such as sample size, workability, and forming pressure when referee testing.
3.2 This practice is applicable for preparing test specimens of various sizes. Note that 9 by 41/2 by 21/2 in. (228 by 114 by 64-mm) samples, because of their large cross-section, have a greater tendency to form flaws during pressing, handling, and drying than smaller cross-sectional samples.
3.3 The purpose of this practice is to minimize flaws in pressed specimens. It is not intended to duplicate all field installation conditions.
3.4 Variations in workability as determined by Test Method C181 can significantly affect the number of flaws contained in a specimen. Establish by mutual agreement the workability level when comparing tests between two laboratories.
3.5 This practice is not intended for preparing specimens of basic ramming mixes, anhydrous tap-hole mixes, nor resin bonded mixes.
Scope
1.1 This practice covers the pressing and drying of chemically and non-chemically bonded alumin-silicate and high alumina plastic and ramming mix refractory specimens classified in accordance with Classification C673.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Domestic orders are delivered via United Parcel Service (UPS) or United States Postal Service (USPS). Transit
times average 3 to 5 business days. Please be aware that UPS will not deliver packages to Post Office Boxes.
International orders are delivered via courier post services which can be either a postal service, courier
service, or a combination of both. Standard Service is untraceable. Please allow 4-7 weeks for delivery.
Please be aware that carriers will not deliver packages to Post Office Boxes. Because of the variability of
customs processes and procedures in different countries, ASTM International cannot guarantee transit times to
international destinations. Customs duty and taxes are the responsibility of the consignee.
Shipping & Handling charges follow the rate schedule, below:
Order Total
Shipping & Handling Fee (US Domestic)
Up to $50.00
$18.72
$50.01 to $100.00
$20.80
$100.01 to $150.00
$29.52
$150.01 to $250.00
$39.09
$250.01 to $500.00
$56.25
$500.01 to $750.00
$76.42
$750.01 to $1000.00
$93.15
$1000.01 to $1500.00
$121.27
$1500.01 to $2500.00
$158.38
$2500.01 to $4999.00
$209.04
$5000.00 to higher
FREE
Order Total
Shipping & Handling Fee (International)
Up to $50.00
$68.72
$50.01 to $100.00
$70.80
$100.01 to $150.00
$79.52
$150.01 to $250.00
$89.09
$250.01 to $500.00
$106.25
$500.01 to $750.00
$126.42
$750.01 to $1000.00
$143.15
$1000.01 to $1500.00
$171.27
$1500.01 to $2500.00
$208.38
$2500.01 to $4999.00
$259.04
$5000.00 to higher
FREE
Shipping and Handling charges are approximate. Additional charges may be incurred if your order requires multiple shipments. This does not apply to complete sets and sections.
